HikvisionCodigo: 3E1505P-EI/M

DS-3E1505P-EI/M Switch GIGA POE Hikvision 4+1 (4 POE 10/100/1000 + 1 UPLINK) Max

❮ ❯

Descripcion

4 Port Gigabit Smart POE Switch

4 × Gigabit PoE port,1 × Gigabit RJ45 port
Total PoE Power Budget 45W
Support 802.1Q VLAN
Support PoE watchdog to detect and restart the cameras that do not respond
Support STP/RSTP Loop prevention
Support cable detection to locate failure
Up to 300 m Long Range PoE Transmission
6KV Surge Protection

General
CarcasaMetal material
Peso neto0.26 kg (0.573 lb)
Peso bruto0.75 kg (1.65 lb)
Dimensiones (W x H x D)121.1 mm × 27.6 mm × 83.1 mm (4.77' × 1.09' × 3.27')
Temperatura de funcionamiento0 °C to 40 °C (32 °F to 104 °F)
Temperatura de almacenamiento-40 °C to 85 °C (-40 °F to 185 °F)
Condiciones de humedad5% to 95% (no condensation)
Humedad relativa5% to 95% (no condensation)
Fuente de alimentación54VDC, 0.92A
Modo de instalaciónDesk-Mounted,Wall-Mounted
Max. El consumo de energía50 W
Consumo de energía en inactivo1 W
Surge Protection6 KV

Parámetros de red
Puertos4 × Gigabit PoE port,1 × Gigabit RJ45 port
Tabla de direcciones MAC2 K
Capacidad de conmutación10 Gbps
Tasa de reenvío de paquetes7.44 Mpps
Caché interna1 Mbits

Fuente de alimentación PoE
PoE StandardIEEE 802.3af,IEEE 802.3at
Pin de alimentación PoEEnd-span: 1/2(-), 3/6(+)
Puerto PoEPoE: Ports 1 to 4
Max. Puerto de alimentación30 W
PoE Power Budget45 W

Función de software
Largo alcance
Ports 1 to 4: up to 300 m.
Long range performance may vary depend on camera model or cable condition.
Port Isolation
Ports 1 to 4: port isolation mode to improve network security
Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
PoE WatchdogPorts 1 to 4: auto detect and restart the cameras that do not respond.
Link Aggregation
Link aggregation is used to aggregate multiple physical ports to form a logical port for load balancing, bandwidth expansion, and port protection.
Support static link aggregation.
Support 1 aggregation groups.
Loop Prevention
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default.
Support 802.1D STP.
Suppport 802.1w RSTP.
VLAN
VLAN is used for network scale planning and network health improvement.
Support 802.1Q.
Configurable VLAN ID from 1-4094.
Support Trunk, Access port mode.
Support Max. 32 VLAN.
HPP
Support one-click activation and remote management via Hik-Partner Pro. Functions supported:
1. Display the port rate.
2. Display the port bandwidth utilization rate.
3. Display the PoE power usage.
4. Display topology information.
5. Display the alarm status.
6. Restart ports and devices.
7. Enable port long-rage mode.
8. Remotely upgrade the device.
System Maintenance
Support device management via web.
Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses.
Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.
Support management via Hik-Central Pro.
Support remote management via Hik-Partner Pro.
Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected.
Supports 802.1ab LLDP for peer device discovery.
Support port mirroring for fault locating.

Certificaciones
EMCCE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1: 2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
SeguridadCB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN 62368-1: 2014+A11: 2017)
QuímicaCE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)